Search Results - KTM ATV Forum

Search:

Type: Posts; User: NeSta75

Page 1 of 2 1 2

Search: Search took 0.03 seconds.

  1. that wossner thing is stressing me out lol , i...

    that wossner thing is stressing me out lol , i already order the piston, worst case, if i dont find, i will return it, and change to the vertex.
    Strange thing about the metal i find before i tear...
  2. Thanks for the information. When you say, i...

    Thanks for the information.
    When you say, i have to feel hand a hair off my combustion chamber, did you mean porting the head ? sorry my english is not to good. Does it mean, i cant just put this...
  3. My other concern is the rocker arms bearing, they...

    My other concern is the rocker arms bearing, they never been change since a buy the quad, and they have 1000 hour easy on it. They seem nice for now, but i know when they fail, it cause a lot of...
  4. So i did a little search last night, i send a...

    So i did a little search last night, i send a email to wossner USA, and thanks to them they respond me (not like wossner germany). They tell me that the reference 8547DA is for 94.95 mm piston,...
  5. Time to rebuild ! Piston choice and others

    Hi

    So i decide to open my engine recently whith 250 hours since last rebuild, i start to have some metal shavings in the short screen. Find out that was some damaged dogs, and worn teeth. So i had...
  6. Problem solved. Finaly its was a wrong cable...

    Problem solved. Finaly its was a wrong cable connection, i conect the blue-red to the yellow-green :lol:(black in my case). Sorry finaly this post is in the wrong section, it must be in XC...
  7. Seems maybe i found the problem (I hope), I check...

    Seems maybe i found the problem (I hope), I check the cables from the gear position sensor, so there are 4 cables (Black,green,blue-red,yellow-green), if i correct, black go to brown, yellow-green,...
  8. I just check out the rpm's, its seem the first...

    I just check out the rpm's, its seem the first gear cut out aroud 3000'4000 rpms more or less, and try the reverse hes go to 6000 and over. i must have switch a cable, cause it's seem like the rear...
  9. First gear act like reverse rear rev limiter

    Hello everyone !

    Recently i had a strange issue, when i put the first gear i can rev correctly, it cut like the reverse gear, but the other gears (2,3,4,5) are fine. First i think it was the first...
  10. Replies
    4
    Views
    429

    Thanks for the info, and the link ;-)

    Thanks for the info, and the link ;-)
  11. Replies
    4
    Views
    429

    hopefully not a big issue, i had a short circuit...

    hopefully not a big issue, i had a short circuit ho melt down my start button, but after inspection he was a cable in bad shape ho toutch the frame. but i strip out the harness for full inspection,...
  12. Replies
    4
    Views
    429

    wiring harness from sx

    I īm having some issues whith my stock wiring harness, 10 years already... I heard the sx wiring is more simple, is it possible to switch on a xc ?
  13. Strange mine dont have any screw here last time i...

    Strange mine dont have any screw here last time i check. many times is the case seal gone bad, and have leack in this specific location. The cause can be to much oil ,or in my case last time i had...
  14. Replies
    27
    Views
    2,344

    Hi sound to me more like the piston in the...

    Hi

    sound to me more like the piston in the master cylinder. Does it do that when you start the quad, or just after a while when you riding ?
  15. Thanks for reply, The bearing was ok when i...

    Thanks for reply,

    The bearing was ok when i check, also nothing strange in the rest of the oil, he was clean. Now i didnt remenber if the shaft was worn my mecanic already putt a new seal, im...
  16. Shaft seal ring behind shift lever blow out

    Hi !

    I had a strange thing happened last race. After the race the bike was running great no problem, then when i shut down the bike, i think some minutes after i wasnt near of it, the shaft seal...
  17. Replies
    10
    Views
    1,176

    Hello everyone ! I come for some news, a...

    Hello everyone !

    I come for some news, a finaly rebuild my engine last month, and finally putt the 8/06 cam, without toutching the piston compretion, and i satisfied whith the litle extra result....
  18. Replies
    10
    Views
    1,176

    that depend on the situation, i think the problem...

    that depend on the situation, i think the problem is i use the bike for different type of riding situation, resistances races (i think is like you call gncc races) but im a novice so maybe the bike...
  19. Replies
    10
    Views
    1,176

    if i go whith this combo, how many hours do you...

    if i go whith this combo, how many hours do you recomand to open engine ?
  20. Replies
    10
    Views
    1,176

    ok thanks for the info. If i put a high...

    ok thanks for the info. If i put a high compression piston i will have to work the head to ? for now i cant put a oil coller, so i guess whith these compression ratio it will heat a litle too much....
  21. Replies
    10
    Views
    1,176

    Ktm 525 xc improvement an reliability

    Hello everyone !

    Im going to rebuild my engine, i read a lot of stuff in this forum but my english is not to good lol, so i want to confirm some things before i messed it up lol.
    I want to make a...
  22. Replies
    21
    Views
    2,557

    That a nice piece of work ! Beautiful exhaust,...

    That a nice piece of work ! Beautiful exhaust, combine with the carb mod must be a good difference. Have to do this mod some day...
  23. Replies
    3
    Views
    616

    Thanks for the answer. ultimately i ride in a lot...

    Thanks for the answer. ultimately i ride in a lot of different ground type. lets say 50 pour-cent sand, and the rest is for mx track ,endurance races type, and some clay ground.
    so no risk of gasket...
  24. Replies
    3
    Views
    616

    1.8 radiator cap information

    Hello everyone !

    I bought recently a radiator cap with a thermometer, but i didn't make attention to the cap pressure, they where listed in ktm xc atv on the site where i bought, so i didn't make...
  25. Replies
    5
    Views
    489

    I buy it, at MGL Graphics, a very talented guy,...

    I buy it, at MGL Graphics, a very talented guy, and not very expansive.
Results 1 to 25 of 27
Page 1 of 2 1 2