Search Results - KTM ATV Forum

Search:

Type: Posts; User: 5.0fox

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    38
    Views
    15,337

    I have a dyna box on my drag bike. It eliminates...

    I have a dyna box on my drag bike. It eliminates all the factory safety features. If your issue is caused by one of the factory safety features putting the dyna ignition on will fix it.
  2. Replies
    3
    Views
    495

    mine is about 15.7:1

    mine is about 15.7:1
  3. torching it works good but it poses a potnetial...

    torching it works good but it poses a potnetial danger if the metal is overheated. A local race team had a auto wheel come apart at 150mph shortly after being powdercoated. Come to find out the...
  4. Replies
    7
    Views
    930

    are you ever down near the us border?

    are you ever down near the us border?
  5. Replies
    10
    Views
    1,318

    Welcome back! Fastest KTM in the nation guys. You...

    Welcome back! Fastest KTM in the nation guys. You couldnt build it for twice the askign price.
  6. Thread: 450 xc partout

    by 5.0fox
    Replies
    13
    Views
    1,211

    what color is the ims tank?

    what color is the ims tank?
  7. Replies
    10
    Views
    1,121

    excessive crank case pressure caused by worn...

    excessive crank case pressure caused by worn rings or an out of round cylinder can blow the seal outwards into the back of the impeller and cause leaks
  8. Replies
    17
    Views
    5,341

    the more pressure put on the crank the more...

    the more pressure put on the crank the more likely it is to spread. Higher engine loads, increased compression, increased rpm, increased piston weight are all factors.
  9. Replies
    17
    Views
    5,341

    i run the 6mm crank just like most all the...

    i run the 6mm crank just like most all the stroker cranks made. For the rod I had a custom short rod made by carrilo to use a standard compression height piston. I run thumpers 14:1 99mm piston with...
  10. Replies
    17
    Views
    5,341

    I ended up going to the billet stroker crank...

    I ended up going to the billet stroker crank offered by crankworks. My stock crank measured .001 out of true so it is still good the weld quality just wasn't sufficient enough for the demanding...
  11. Replies
    17
    Views
    5,341

    Did you happen to have DJH do the crank work? I...

    Did you happen to have DJH do the crank work? I had him rebuild one for me last season and it only made it 11 hours before the welds broke. The unwelded stock crank lasted longer then that
  12. Replies
    1
    Views
    460

    WTB +6-+8 swingarm

    Im looking for a +6-+8 swingarm for my build. anyone got one available? Cash in hand or I can trade a +4. post here or shoot me a text (253)954-6947
  13. Thread: KTM drag bike

    by 5.0fox
    Replies
    4
    Views
    728

    Shoot me a text. I recently built a bike that...

    Shoot me a text. I recently built a bike that really pushed the boundaries of the rfs. There's some things you should know before you start. My names Jake and my number is (253)954-6947
  14. Thread: KTM drag bike

    by 5.0fox
    Replies
    4
    Views
    728

    There are no drag pipes available. What I did for...

    There are no drag pipes available. What I did for my bike was cut a ktm bill can down to 10" and machine the tip open to match the diameter of some other model drag pipes. I saw a little gain from...
  15. Replies
    4
    Views
    734

    How old is the battery? Charge it up then unplug...

    How old is the battery? Charge it up then unplug it from the bike for two days and see if it is still holding a charge. You might just have a bad battery
  16. Replies
    4
    Views
    664

    the hub pictured is not an oem ktm hub. I dont...

    the hub pictured is not an oem ktm hub. I dont recall ever seeing those hubs before.
  17. Replies
    7
    Views
    2,533

    Im one of the guys who has had some problems with...

    Im one of the guys who has had some problems with work he has done for me. When he bored an fcr for me he got it off center and broke through the side of The carb. Problem number two is a crank I had...
  18. How much for subframe?

    How much for subframe?
  19. Replies
    5
    Views
    812

    I love the way my high compression motors have...

    I love the way my high compression motors have run. You won't regret going higher then 12.5:1. Dont worry about the starter. My 15:1 600cc build cranks over just fine.
  20. Replies
    12
    Views
    1,159

    Do you have an xc wiring harness?

    Do you have an xc wiring harness?
  21. Replies
    16
    Views
    4,179

    the weight savings come from all over the bike...

    the weight savings come from all over the bike really. the shocks, wheels and tires, swingarm, aluminum axle, and removing the front brake system made up most of it. As for the HSR carb I havent done...
  22. Replies
    16
    Views
    4,179

    Kiwi this thing sounds rediculous. The extra...

    Kiwi this thing sounds rediculous. The extra displacement and compression plus the larger exhaust opening made a huge difference. Dylan Im not really sure how it will compare but I should get the...
  23. Replies
    16
    Views
    4,179

    I don't have a very accurate scale but it is...

    I don't have a very accurate scale but it is right around 275 with 1/2 tank
  24. Replies
    502
    Views
    216,895

    Sticky: here is my latest build. More info in this...

    here is my latest build. More info in this thread:
    http://www.ktmatvhq.com/forum/pictures-videos/12748-2014-dune-drag-build.html#post95414
  25. Replies
    33
    Views
    7,514

    I have an updated thread on this bike at the...

    I have an updated thread on this bike at the following link:

    http://www.ktmatvhq.com/forum/pictures-videos/12748-2014-dune-drag-build.html#post95414
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4