2009 ktm 505 sx pro level race quad
Results 1 to 10 of 10
  1. #1
    Member Rookie
    Join Date
    Sep 2012
    Posts
    88

    2009 ktm 505 sx pro level race quad

    I have a 2009 ktm 505 sx pro level race quad for sale. The bike was just recently finished from a ground up rebuild. This bike is in showroom condition. Every bearing, seal, working part, or damaged part was replaced. every part is powdercoated, polished, or cleaned to perfection. The bike hour meter shows 8.6 hours. unless noted all parts below were brand new at that time. I have a little over 20k in the bike so please no low ball offers. i am asking 11k, i know you can not re build it for that i jut did it. I am only selling it because i got hurt pretty bad and can not ride for a while so i want to start a new project to pass the time. i would consider a trade for honda and some cash. If you come look at the bike or i ship it to you and it not as clean as described i will cover your travel cost or cover the cost to ship it back


    chassis-all parts new unless noted. all bearings, bushings, or ball joints brand new

    stock frame-original frame with title. new ktm orange coat
    walsh long travel arms candy purple coat
    stock swing arm.ktm bill chain guide bracket and td chain guide. all balls bearings. candy purple coat
    rath pro serries nerfs with ponster peg. candy purple coat
    rath grab bar and front bumper. candy purple coat
    precision stabilizer-1 season of use
    pep built wp shocks. tripple rate front. dual rate rear. one season old. just freshened. new ktm orange coat on spings 190 lb a class mx set up( these are great shocks)
    xstreme composites + 1 carbon stem
    xstrmem composites carbon brake stay
    ktm bill race harnes-no key
    oem front and rear fenders-white. oem side shrouds black
    quad tech carbon hood
    ftr custom graphics-ernie at ftr can print name plates with your info on them to exchange
    jet trim seat cover with kevlar sides
    renthal gold atv x ring chain
    sidewinder sprocket
    rpm dominator II axle
    rpm tapered bearing carrier
    new pivot bolt and nut
    dwt wheels flat black
    maxxis yellow lable tires
    hubs coated flat black new all balls bearings
    streamline brake pads
    pro taper fat bars
    oury clamp grips
    ktm bill batt re locate box and wiring

    engine-every bearing seal is new. all other parts are new unless noted and if they are not new they have been completely frehend up

    ktm oem 505 piston-new
    ktm oem 505 cylinder decked .012 for 13.5 ratio with stock piston-new
    pro x rod and bearing-new
    crankshaft-freshend by rage atv
    crower victory intake cam-new
    rage atv full race port and valve job-used head port job new
    rage atv 43mm race carb-used carb race prep and bore new
    tjm manual chain guide-new
    wiesco main bearings-new
    wiesco billet basket and honda fibers-new
    transmision-rebuilt and freshened
    oil pumps-new
    ktm bill race exhaust
    vortex x-10 ignition

    on the highest setting on the ignition this is a 60hp engine and it has a ton of torque. i am around 200lbs and i still generally ride it in a lower setting becasue it pulls so hard. very very strong motor


    2009 ktm 505 sx pro level race quad-053-545x363-.jpg2009 ktm 505 sx pro level race quad-052-545x363-.jpg2009 ktm 505 sx pro level race quad-051-545x363-.jpg2009 ktm 505 sx pro level race quad-050-545x363-.jpg2009 ktm 505 sx pro level race quad-046-545x364-.jpg

  2. #2
    Member Rookie
    Join Date
    Sep 2012
    Posts
    88
    any interest? Price range thoughts?

  3. #3
    Member Rookie
    Join Date
    Sep 2012
    Posts
    88
    may conider a part out if you guys show some interest. i would need to sell the motor first though. also would consider changing ignition, stem, and a couple small parts and reduce the price. Make me some offers.

  4. Remove Advertisements
    KTMATVHQ.com
    Advertisements
     

  5. #4
    Junior Member Rookie
    Join Date
    Mar 2013
    Posts
    18
    Sure wouldn't mind having that quad tech hood, and maybe white plastics depending on condition! Thanks

  6. #5
    Member Rookie
    Join Date
    Sep 2012
    Posts
    88

    parts

    Everything on the quad is brand new but I wouldnt really want to start parting it out until I havev a buyer on the motor
    Last edited by broberts; 04-08-2013 at 05:03 PM.

  7. #6
    Member Rookie
    Join Date
    Sep 2012
    Posts
    88
    bump $8500. willing to ship if needed

  8. #7
    Junior Member Rookie
    Join Date
    Nov 2009
    Location
    Durham, Ct. USA
    Posts
    10
    Sent you a PM

  9. #8
    Senior Member Member
    Join Date
    Apr 2012
    Posts
    117
    Is it still for sale?

  10. #9
    Junior Member Rookie
    Join Date
    Feb 2015
    Posts
    3
    where are you

  11. #10
    Junior Member Rookie
    Join Date
    Nov 2019
    Location
    Minnesota
    Posts
    10
    Umm, you do realize that this ad is almost 7 years old and the OP's last activity on the forum was in April of 2013? Best bet is to try Facebook Marketplace and expand the search area to 1999 kilometers. That's how I found mine, 13 hours away, but I found one.


 

Sponsored Links

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Search tags for this page

ktm quad for sale

,

quad ktm 505

,

quad ktm rasing

,

race prep atv for sale miami

,

walsh racing quad ktm

Click on a term to search for related topics.